Kathrein UFD 515 Manuel d'utilisateur

Operating Manual Order no.: 260 473

Control, displays and connection Remote control handset keys A / BMF LO KT VMCalls up main menue Power On - Standby A Switch over of the remote cont

Command of the remote control Command of the remote control The remote control features 2 command sets, making it possible to operate 2 receivers inde

Operating instructions Operating instructions Menu concept The menu concept is based on a logical operation sequence. Note: Coloured backgroun

Operating instructions Alphanumeric assignments of number buttons on the remote control Button 1 X 2 X 3 X 4 X 1 1 Q Z - 2 2 A B C 3 3 D

Connection and start-up Connection and start-up The following section is specifically intended for the specialist dealer. You only need to read this s

Connection and start-up LNB-supply voltage If the feed system (LNB) is powered by an external supply voltage and the LNB supply voltage is not used fo

First time installation First time installation The first steps Connect the receiver to the mains power supply. Switch on the receiver by pressing th

On screen displays On screen displays Important screen displays The receiver functions are controlled by a microprocessor and extensive software. The

On screen displays favourite or standard programme and the parental control is provided in the column below the symbol. The column on the left contain

Programme selection Programme selection This section describes how you select analogue and digital TV programme with your receiver and how you can set

Programme selection TV programme selection by number entry You can select a different TV programme during a current TV programme by enter-ing the prog

Programme selection By pressing the oubuttons you jump to the next programme and by press-ing the -+buttons you jump to the neighbouring page or enter

Common Interface Common Interface You will find the Common Interface for the insertion of two so-called conditional ac-cess modules behind the front

Timer settings Timer settings You can use the timer for recording a programme with a video recorder on time. Seven timers are available which you can

Programme overview Programme overview EPG With the z button, you receive an overview of the programmes (see on-screen display) currently received from

Sound settings Sound settings Setting the volume Set the required volume level by pressing the -+ buttons on the remote control of the receiver. A bar

Programme list Programme list The programmes /channels set at the factory can be changed in the " programme list" menu. Select the menu by p

Programme list Programme assortment You can sort programmes as desired. The programmes are sorted by shifting the entries in the programme lists. Pres

Programme list The highlighted line can now be prepared for deletion by pressing the O button. The control programme now asks: "Do you want to de

Programme list Only alphanumerical and decimal entries are accepted at the positions name, · · · · · video PID (programme identification), audio PID,

Preface Preface Dear Customer, The following operating manual will help you obtain the best optimal use from the extensive features of your new

Adding/removing satellites Adding/removing satellites Setting up a satellite The LNB can naturally also accommodate new satellites. For this, the orbi

Adding/removing satellites Remove satellite To remove a satellite, select the "LNB configuration" menu, move the cursor bar with o or u and

Password Password You can prevent your satellite receiver to be used by unauthorised persons by means of a password. With this password, you can ensur

Password Parental lock You can set parental lock in a manner similar to that used for marking favourite programmes by means of the "Apple" s

Operation from the front panel Operation from the front panel If you have misplaced the remote control or the batteries are empty, you can still opera

Setting system parameters Setting system parameters The following settings should not be altered without good reason, since they are factory presets o

Setting system parameters remote control, otherwise the settings will be lost. Timer menu See section "Timer settings." Summer time See abov

Setting system parameters OSD colour Use the -+ buttons to select the background colour of the on-screen display. Confirm by pressing L two times. OSD

Installation menu Installation menu You should not change the following settings without good reason as they repre-sent factory settings or operationa

Installation menu Changing the oscillator frequency Move over to the right-hand side in the LNB configuration menu by pressing O and the setting for L

Contents Contents Preface ...

Installation menu DiSEqC setting The precondition for this setting is that you have made no changes in the DiSEqC (UFO) set-up, refer to the section &

Installation menu The signal quality and the search progress are indicated during the search. The message appears at the end of the search. All new

Installation menu ponders. After an unsuccessful search the following message appears: Error All new programmes are added to the existing programme

Installation menu Tone Burst Under this menu point, the 22 kHz signal can be set as follows: : Switching statuses of setting Switching statuses

Installation menu A remote frequency must not be set in this operating mode, because it is defined by the UFO micro system as part of the addressing

Video recorder connection Video recorder connection The connection diagram provided at the end of this User's Guide and the descrip-tion of the v

Software and programme lists update Software and programme lists update Thanks to digital technology, the software and programme list of your receiver

Data transfer from receiver to receiver Data transfer from receiver to receiver Your receiver is able to accept data from another receiver via the RS2

Technical annex Technical annex Technical features The receiverUFD 515 is equipped with the following features: Reception of all digital TV programmes

Technical annex Technical data RF features Sat-IF frequency range 950 to 2150 MHz Input level range 43 to 83 dBµV IF frequency 479,5 MHz Receiving

Contents Reception status - radio ...

Technical annex Accessories 1 Infrared remote control 2 Batteries 1.5 V, type: LR 03, size: AAA (Micro) 1 SCART cable 1 Set of operating instructions

Technical annex Connection examples VCRTVIF INPUT DIGITAL920-215 0MHz14/1 8V max. 400mA22kHzVCRAUXUFD 505 260494TVIF OUTPUTDiSEqC 1.1DATA I/OAC 8

Technical annex Connection arrangement 2: VCRTVDecoderUFD 400 260440230V~50Hz21WattDATAI/OTVIF INPUT920-2150MHz14/18V max . 400mA22kHzAUDI O-OUTT

Glossary, abbreviations Glossary, abbreviations Audio output Receiver sound output AV channel slot Preferential channel location of TV set for SCART

Short technical lexicon Short technical lexicon DiSEqC DiSEqC (Digital Satellite Equipment Control) is a communication system between the Sat receiver

Short technical lexicon ceived per second. Transponder A transponder is a satellite transmitter which transmits TV and radio signals. A satellite ha

Service Service OSD-Language Picture format LNB supply German 4:3 Operation: Standby: ON 16:9 OF

998.6247/1001/ZWT Subject to technical changes! internet http://www.kathrein.de KATHREIN-Werke KG  Telefon (0 80 31) 18 40  Fax (0 80 31) 18 43 0

Contents Transponder selection ...

Safety instructions Safety instructions Important notes regarding operation The following section contains important information relating to the oper

Safety instructions Important notes for siting and installation. Place of installation Every electronic device generates heat. The rise in temperature

Control, displays and connection Control, displays and connection This section contains a brief description of all the control elements, displays and