Operating Manual Order no.: 260 498
Controls, displays and connections Remote control handset keys A / BMF LO KT VMCalls up main menue Power On - Standby A Switch over of the remote co
Command of the remote control Command of the remote control The remote control features 2 command sets, making it possible to operate 2 receivers inde
Operating instructions Operating instructions Menu concept The menu concept is based on a logical operation sequence. Note: Coloured backgrounds are
Operating instructions Alphanumeric assignments of number buttons on the remote control Button 1 X 2 X 3 X 4 X 1 1 Q Z - 2 2 A B C 3 3 D
Connection and start-up Connection and start-up The following section is specifically intended for the specialist dealer. You only need to read this s
Connection and start-up LNB-supply voltage If the feed system (LNB) is powered by an external supply voltage and the LNB supply voltage is not used fo
First time installation First time installation The first steps Connect the receiver to the mains power supply. Switch on the receiver by pressing the
On screen displays On screen displays Important screen displays The receiver functions are controlled by a microprocessor and extensive software. The
On screen displays provided in the column below the symbol. The column on the left contains informa-tion relating to the channel, the programme provid
Programme selection Programme selection This section describes how you select analogue and digital TV programme with your receiver and how you can set
Programme selection Reception status analogue When you receive an analogue programme, you can also call up other programmes with the ou buttons. Anal
Programme selection Reception status - radio After the switch-over of the receiver, simply press the oubuttons to select other radio programmes in the
Timer settings Timer settings You can use the timer for recording a programme with a video recorder on time. Seven timers are available which you can
Sound settings Sound settings Setting the volume Set the required volume level by pressing the -+ buttons on the remote control of the receiver. A bar
Programme list - TV/radio Programme list - TV/radio The programmes /channels set at the factory can be changed in the " programme list" menu
Programme list - TV/radio Programme assortment You can sort programmes as desired. The programmes are sorted by shifting the entries in the programme
Programme list - TV/radio The highlighted line can now be prepared for deletion by pressing the O button. The control programme now asks: "Do you
Programme list - TV/radio Only alphanumerical and decimal entries are accepted at the positions name, · · · · · video PID (programme identification),
Adding/removing satellites Adding/removing satellites Setting up a satellite The LNB can naturally also accommodate new satellites. All new settings m
Adding/removing satellites To enter a satellite name You can change the satellite names in the LNB configuration menu with the num-ber buttons. Refer
Preface Preface Dear Customer, The following operating manual will help you obtain the best optimal use from the extensive features of your new
Programme overview Programme overview EPG With the z button, you receive an overview of the programmes (see on-screen display) currently received from
Password Password You can prevent your satellite receiver to be used by unauthorised persons by means of a password. With this password, you can ensu
Password Here, use the ou buttons to select the "Programme list" entry. Using the -+ buttons, you can now specify whether you want to edit t
Password Operation from front panel If you have misplaced the remote control or the batteries are empty, you can still operate you receiver from the
Setting system parameters Setting system parameters The following settings should not be altered without good reason, since they are factory presets o
Password Summer time See above. Changeover in spring or fall. Confirm by pressing L two times. TV type Use the -+ buttons to specify whether your
Setting system parameters OSD trans Use the -+ buttons to select the transparency of the background colour. Confirm by pressing L
Password Installation menu You should not change the following settings without good reason as they repre-sent factory settings or operational settin
Installation menu Changing the oscillator frequency Move over to the right-hand side in the LNB configuration menu by pressing O and the setting for L
Password DiSEqC setting The precondition for this setting is that you have made no changes in the DiSEqC (UFO) set-up, refer to the section "Di
Contents Contents Preface ...
Installation menu The message appears at the end of the search. All new programmes are added to the existing programme list. You can interrupt the
Installation menu After an unsuccessful search the following message appears: Error All new programmes are added to the existing programme list. Und
Installation menu Tone Burst Under this menu point, the 22 kHz signal can be set as follows: : Switching statuses of setting Switching statuses
Installation menu A remote frequency must not be set in this operating mode, because it is defined by the UFO micro system as part of the addressing
Analogue setting Analogue setting In general, you do not need to alter the analogue programmes. New analogue pro-grammes are unlikely to appear due to
Analogue setting Decoder For connect of the decoder to the VCR/AUX socket, set the associated decoder mode. Please obtain the relevant details from th
Analogue setting Frequency left/right Here, you can select one of two sound carriers. For example, in the case of com-mentary channels or film broad
Video recorder connection Video recorder connection The connection diagram provided at the end of this User's Guide and the descrip-tion of the
Analogue decoder connection Analogue decoder connection You can also connect a decoder to the UFD 520 receiver for analogue pay-TV pro-grammes. since
Software and programme lists update Software and programme lists update Thanks to digital technology, the software and programme list of your receiver
Contents Reception status - radio ...
Data transfer from receiver to receiver Data transfer from receiver to receiver Your receiver is able to accept data from another receiver via the RS2
Technical annex Technical annex Technical features The receiver UFD 520 is equipped with the following features: Reception of all digital TV programm
Technical annex Technical data RF-features Sat-IF frequency range 2 x 950 to 2150 MHz Input level range analogue digital 48 to 78 dBµV 43 to 83 dB
Technical annex Accessories 1 Infrared remote control 2 Batteries 1.5 V, type: LR 03, size: AAA (Micro) 1 SCART cable 1 Mains cable 1 Coax-bridge for
Technical annex Connection examples Connection arrangement 1: Connection of a DVB-S satellite receiver to a receiving system. I F I N P U T D I G
Technical annex Connection arrangement 2: Reception of digital programmes of satellite system ASTRA and EUTELSAT via a multifeed antenna with 2 Quatro
Glossary, abbreviations Glossary, abbreviations Audio output Receiver sound output AV channel slot Preferential channel location of TV set for SCART
Short technical lexicon Short technical lexiconAC3 Audio coding MPEG 2/layer 3 - The scrambled digital sound signal for Dolby Digi-tal. It transmi
Short technical lexicon Symbol rate The symbol rate describes the amount of data transmitted per second. The symbol rate is measured in MSymbols/s and
Service Service OSD-Language Picture format LNB supply German 4:3 Operation: Standby: ON 16:9
Contents Transponder selection ...
998.6248/1001/ZWT Subject to technical modifications! internet http://www.kathrein.de KATHREIN-Werke KG Telefon (0 80 31) 18 40 Fax (0 80 31)
Safety instructions Safety instructions Important notes regarding operation The following section contains important information relating to the oper
Safety instructions Important notes for siting and installation. Place of installation Every electronic device generates heat. The rise in temperature
Controls, displays and connections Controls, displays and connections This section contains a brief description of all the control elements, displays
Commentaires sur ces manuels